Skip to content

Cart

Your cart is empty

Article: Will a wedding ring sit flush with your engagement ring? Decide before you buy

Buying guide

Will a wedding ring sit flush with your engagement ring? Decide before you buy

The short answer: every engagement ring will one day sit next to a wedding ring, so choose the engagement ring with that in mind. The thing that matters most is how high the stone is set. If it is set too low, the stone and its setting sit in the way and a straight wedding band cannot sit flush. You are left with a gap between the two rings.

It is the most common thing people wish they had been told. It costs nothing to get right at the start and it is awkward to fix afterwards.

Diagram: a low set engagement ring leaves a gap beside the wedding ring, a raised setting lets the wedding ring sit flush

Why does a low setting leave a gap?

A diamond is wider than the band it sits on. In a low setting the widest part of the stone, and the metal basket holding it, sits right down at finger level. It sticks out past the edge of the band.

When a straight wedding ring is pushed up against it, it hits the setting before it reaches the band. The two bands never touch.

In a raised setting the stone is lifted clear of the band. The wedding ring slides underneath the stone and sits tight against the engagement ring. That is what jewellers mean by flush fit or wed-fit.

How high should an engagement ring be set?

High enough for a band to pass underneath the stone, and no higher. As a guide, the underside of the setting needs to clear the top of the wedding band you plan to wear. Most wedding bands are between 1.5mm and 2mm deep.

Going higher than you need has a cost. A tall setting catches on hair, knitwear and pockets, and takes more knocks. The aim is the lowest setting that still lets the wedding ring sit flush.

Which engagement ring styles sit flush with a straight wedding band?

Engagement ring style Straight wedding band What to know
Raised solitaire, four or six claw Usually sits flush The simplest ring to pair
Cathedral setting Usually sits flush The shoulders rise to meet the stone and leave room beneath
Low set solitaire or basket Leaves a gap Needs a shaped band, or a higher setting
Bezel or rub-over, set low Leaves a gap Ask for it to be raised if you want a flush fit
Halo Depends on height The halo makes the head wider, so it needs more clearance
Three stone (trilogy) Depends on height Three settings to clear instead of one
Oval, pear or marquise set across the finger Usually leaves a gap The stone overhangs the band on both sides

What if I want a low set engagement ring?

Low settings are popular for good reason. They are comfortable, they suit active hands and they fit under gloves. You can still have one. You have three options for the wedding ring.

  • A shaped wedding band. Also called a curved, contoured or wishbone band. It is made to follow the outline of your engagement ring so the two lock together.
  • A notched band. A straight band with a small cut-out where the setting sits.
  • Wear the gap. Some people like the look of a small space between the rings. That is a fair choice, as long as it is a choice.

The trade-off with a shaped band is that it only looks right next to that one engagement ring. Worn alone, the curve is obvious.

What else affects how the two rings sit together?

Metal

Two rings rub against each other every day for decades. Choose the same metal for both. A harder metal will slowly wear away a softer one, so platinum next to 9ct gold is a poor match. Platinum with platinum, or 18ct with 18ct, wears evenly.

Band width and profile

The rings look like a pair when the bands are a similar width and the same profile. A rounded court band next to a flat band leaves a visible V between them.

Diamonds on the side of the band

Diamond is harder than any metal. If the engagement ring has diamonds set along its edge, they can wear a groove into the wedding ring over time. Leave the touching sides plain metal where you can.

Ring size

Two rings together cover more of the finger and feel tighter than one. Tell your jeweller you plan to stack, so the sizes can be set with that in mind.

What to ask before you buy the engagement ring

  1. Will a straight wedding band sit flush against this ring?
  2. If not, can the setting be raised?
  3. How much clearance is there under the stone, in millimetres?
  4. Can you make a matching wedding band later, in the same metal?
  5. Is there anything on the side of the band that will rub?

If the ring is a surprise, question one is the one to remember.

Common questions

Does every engagement ring need a wedding ring to match?

In the UK most people wear both on the same finger, with the wedding ring nearest the hand. So the engagement ring will almost always end up next to a second ring. It is worth planning for even if the wedding is years away.

What is a flush fit or wed-fit engagement ring?

It is an engagement ring with the stone set high enough for a straight wedding band to sit tight against it, with no gap between the two bands.

Can a jeweller raise the setting on a ring I already own?

Sometimes. On many rings the head can be rebuilt or replaced with a taller one. It depends on how the ring was made. A shaped wedding band is often the simpler fix.

Is a high setting less secure?

Not if it is well made. A taller setting is more exposed to knocks, so the claws should be checked from time to time. A setting raised only as far as it needs to be is a good balance.

Should I buy the engagement ring and wedding ring together?

You do not need to. You do need to know the wedding ring will fit when the time comes. Having both made by the same jeweller, in the same metal, is the easiest way to be sure.

How we can help

When you choose a setting in our ring studio, ask us whether it will take a flush wedding band before you order. If you want a setting adjusted or a wedding ring shaped to fit a ring you already have, that is what our bespoke service is for.

Still choosing the stone? Start with the 4Cs of diamonds and lab-grown vs natural diamonds.

Call +44 7898 659493 or visit us at 81 to 83 Spencer Street in Birmingham's Jewellery Quarter, Monday to Saturday, 9am to 6pm.

Read more

Buying guide

The 4Cs of diamonds explained, plus three more worth knowing

Cut, colour, clarity and carat decide how a diamond looks and what it costs. Certificate, shape and cost finish the picture. A plain-English guide to all seven, with the grades we would pick for an...

Read more
Buying guide

Lab-grown vs natural diamonds: what is the same, what is different and where the value comes from

A lab-grown diamond and a natural diamond are the same material. They differ in where they came from, what they cost and what they are worth later. A straight comparison from a jeweller who sells b...

Read more